AS NZS 4129 pdf download

AS NZS 4129 pdf download,Fittings for polyethylene (PE) pipes for pressure applications
1.1  Scope
This Standard specifies requirements for fittings to be used with polyethylene pipe manufactured in accordance with AS/NZS 4130 or AS 2698.2 or POP 009. This Standard is applicable to fittings manufactured for the conveyance of water, fuel gas, and other fluids including compressed air. NOTE  For continuous use at temperatures above 20 °C refer to AS/NZS 2033 for polyethylene materials. Section 1 specifies general requirements that apply to all fittings except where subsequent sections detail or exempt specific requirements for particular types of fittings. This Standard is not applicable to fittings that achieve end‑load restraint by processes that reduce pipe and/or fitting spigot thickness to < 0.9 T min as defined by AS/NZS 4130. Requirements for demonstrating conformity to this Standard are specified in Appendix A.
1.2  Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. NOTE  Documents referenced for informative purposes are listed in the Bibliography. AS 1049, Telecommunication cables — Insulation, sheath and jacket AS 1145.2, Determination of tensile properties of plastics materials, Part 2: Test conditions for moulding and extrusion plastics AS 1199.1, Sampling procedures for inspection by attributes, Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection AS 1722.2, Pipe threads of Whitworth form, Part 2: Fastening pipe threads AS 2129, Flanges for pipes, valves and fittings AS 2193, Calibration and classification of force-measuring systems AS 2345, Dezincificaton resistance of copper alloys AS 2698.2, Plastics pipes and fittings for irrigation and rural applications, Part 2: Polyethylene rural pipe AS 3688, Water supply — Metallic fittings and end connectors AS ISO 7.1, Pipe threads where pressure-tight joints are made on the threads — Dimensions, tolerances and designation AS/NZS 2280, Ductile iron pipes and fittings AS/NZS 3500.0, Plumbing and drainage, Part 0: Glossary of terms AS/NZS 4020, Products for use in contact with drinking water AS/NZS 4087, Metallic flanges for waterworks purposes AS/NZS 4130, Polyethylene (PE) pipes for pressure applications AS/NZS 4131, Polyethylene (PE) compounds for pressure pipes and fittings AS/NZS 4158, Thermal-bonded polymeric coatings on valves and fittings for water industry purposes AS/NZS 4331.1, Metallic flanges, Part 1: Steel flanges AS/NZS 4331.2, Metallic flanges, Part 2: Cast iron flanges AS/NZS 4331.3, Metallic flanges, Part 3: Copper alloy and composite flanges AS ISO/IEC 17025, General requirements for the competence of testing and calibration laboratories ISO 228‑1, Pipe threads where pressure-tight joints are not made on the threads — Part 1: Dimensions, tolerances and designation ISO 1043‑1, Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics ISO 1133‑1, Plastics — Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics — Part 1: Standard method ISO 1167‑1, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 1: General method ISO 1167‑2, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces ISO 1167‑4, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 4: Preparation of assemblies ISO 3126, Plastics piping systems — Plastics components — Determination of dimensions ISO 3459, Plastic piping systems — Mechanical joints between fittings and pressure pipes — Test method for leaktightness under negative pressure ISO 3501, Plastics piping systems — Mechanical joints between fittings and pressure pipes — Test method for resistance to pull-out under constant longitudinal force ISO 3503, Plastics piping systems — Mechanical joints between fittings and pressure pipes — Test method for leaktightness under internal pressure of assemblies subjected to bending ISO 4427‑3, Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply, Part 3: Fittings ISO 7686, Plastics pipes and fittings — Determination of opacity ISO 9080, Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation ISO 9624, Thermoplastics piping systems for fluids under pressure — Flange adapters and loose backing flanges — Mating dimensions ISO 11357‑6, Plastics — Differential scanning calorimetry (DSC) — Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) ISO 11413, Plastics pipes and fittings — Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting ISO 12176‑2, Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 2: Electrofusion ISO 12176‑4, Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 4: Traceability coding ISO 13460‑1, Agricultural irrigation equipment — Plastics saddles — Part 1: Polyethylene pressure pipes