AS NZS 2205.3.1 pdf download
AS NZS 2205.3.1 pdf download.Destructive tests on welds in metallic materials 1 Scope This International Standard specifies a method for making transverse root, face and side bend tests on test specimens taken from butt welds, butt welds with cladding (subdivided into welds in clad plates and clad welds) and cladding without butt welds, in order to assess ductility and/or absence...
AS NZS 1335 pdf download
AS NZS 1335 pdf download.Gas welding equipment — Rubber hoses for welding, cutting and allied processes 1 Scope This document specifies requirements for rubber hoses (including twin hoses) for welding, cutting and allied processes. This document specifies requirements for rubber hoses for normal duty of 2 MPa (20 bar) and light duty [limited to hoses for maximum working pressure of...
AS NZS 2632.2 pdf download
AS NZS 2632.2 pdf download.Codes for the representation of names of countries and their subdivisions 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. ISO and IEC maintain terminological databases for use in standardization at the following addresses: — ISO Online browsing platform: available at https:// www .iso .org/ obp — IEC Electropedia:...
AS NZS 2845.3 pdf download
AS NZS 2845.3 pdf download.Water supply — Backfow prevention devices 1.1 Scope This Standard specifies requirements for field testing and maintenance of the following backflow prevention devices: (a) Registered break tank (RBT). (b) Registered air gap (RAG). (c) Pressure-type vacuum-breaker (PVB). (d) Spill resistant pressure vacuum-breaker (SPVB). (e) Reduce-pressure-zone device (RPZD). (f) Double check valve (DCV). (g) Reduced-pressure-detector assembly (RPDA)....
AS NZS 2632.1 pdf download
AS NZS 2632.1 pdf download.Codes for the representation of names of countries and their subdivisions 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. ISO and IEC maintain terminological databases for use in standardization at the following addresses: — ISO Online browsing platform: available at https:// www .iso .org/ obp — IEC Electropedia:...
AS NZS 1158.2 pdf download
AS NZS 1158.2 pdf download.Lighting for roads and public spaces 1.1 SCOPE This Standard specifies the computer-based design procedures applicable to Category V and Category P lighting for the calculation of light technical parameters (LTPs), as required, for the design or evaluation of road lighting in accordance with the requirements of AS/NZS 1158.1.1 and AS/NZS 1158.3.1. It gives the basic...
AS NZS 1158.3.1 pdf download
AS NZS 1158.3.1 pdf download.Lighting for roads and public spaces 1.1.1 Scope This Standard specifies performance and design requirements for Category P lighting schemes as described in AS/NZS 1158.0. It also specifies the luminaire data and other data that is needed to facilitate the lighting design and the assessment of conformance to the requirements of this Standard. This Standard assigns...
AS NZS 2280 pdf download
AS NZS 2280 pdf download,Ductile iron pipes and fttings 1.1 Scope This Standard specifies requirements for ductile iron pressure pipes centrifugally cast in moulds, and ductile iron fittings of nominal sizes up to and including DN 750. NOTE 1 Ductile iron is also known as spheroidal graphite iron, SG iron or nodular graphite iron. The specified pipes and fittings are...
AS NZS 2785 pdf download
AS NZS 2785 pdf download.Suspended ceilings — Design and installation 1.1 Scope This Standard sets out the minimum requirements for the design, construction, installation, maintenance, and testing of internal and external non-trafficable suspended ceiling systems of dry construction with suspension systems attached to a supporting structure. It is intended for use in commercial and industrial applications. This Standard also applies...
AS NZS 2885.2 pdf download
AS NZS 2885.2 pdf download.Pipelines — Gas and liquid petroleum 1.1 Scope This Standard specifies minimum requirements for safety, welding consumables, weld preparations, welding processes, qualifications of welding procedures and personnel, and fabrication and inspection requirements for the construction and maintenance welding of carbon and carbon-manganese steel pipelines down to 3.2 mm wall thickness designed and constructed in accordance with...