API Spec 1590 pdf download
API Spec 1590 pdf download.SPECIFICATIONS AND QUALIFICATION PROCEDURES FOR AVIATION FUEL MICROFILTERS 3.1.3 Flow rate Elements with a nominal 150 mm (nominal 6 in.) outside diameter shall meet the performance specification at a minimum flow rate of 10 l/sec/m of effective media length (equivalent to 6 l/min/cm or approximately 4 US Gal./min/in). Manufacturers may qualify elements at higher flow rates...
API Publ 4720 pdf download
API Publ 4720 pdf download.Comparison of API and EPA Toxic Air Pollutant Emission Factors for Combustion Sources 2 COMPARISON OF PUBLISHED EMISSION FACTORS The two primary sources of published emission factors for air toxics from combustion processes are the EPA’s AP-42 document and the API’s Petroleum Air Toxics Emission Factors (PATEF) database. The EPA periodically updates emission factors to incorporate...
API Publ 4717 pdf download
API Publ 4717 pdf download.PREDICTORS OF WATER-SOLUBLE ORGANICS (WSOs) IN PRODUCED WATER—A LITERATURE REVIEW 2 Chemical Composition of Produced Water 2.1 ORIGINS OF PRODUCED WATER During millions of years of geologic time, petroleum and natural gas may accumulate in porous sediments (e.g., sands) trapped between layers of impermeable rock deep within the earth (Collins, 1975). Water may be trapped during...
API Publ 4714 pdf download
API Publ 4714 pdf download.A Guide to Polycyclic Aromatic Hydrocarbons for the Non-Specialist 2 Sources of PAHs PAHs are produced in nature through four generalized pathways: 1) low temperature diagenesis of organic matter (part of the changes undergone by a sediment after its initial deposition); 2) the formation of petroleum and coal; 3) incomplete or inefficient combustion at moderate to...
API PUBL 4713 pdf download
API PUBL 4713 pdf download.Characterization of Fine Particulate Emission Factors and Speciation Profiles from Stationary Petroleum Industry Combustion Sources This report presents results of a pilot project to evaluate the test protocol on a refinery fluid catalytic cracking unit (FCCU). The FCCU tested is a partial combustion unit with a process capacity of 47,000 barrels per day. The CO-rich offgas...
API Publ 1645 pdf download
API Publ 1645 pdf download.Stage II Vapor Recovery System Operations & System Installation Costs 1 Executive Summary Stage II vapor recovery is a well-known air quality control measure that reduces ozone precursors from gasoline dis- pensing facilities (GDFs). As a result of its relative high- visual proÞle, Stage II vapor controls are sometimes proposed as a part of a regional...
API RP 14J pdf download
API RP 14J pdf download.Recommended Practice for Design and Hazards Analysis for Offshore Production Facilities 1 General 1.1 PURPOSE The purpose of this recommended practice is to assemble into one document useful procedures and guidelines for plan- ning, designing and arranging offshore production facilities, and performing a hazards analysis on open-type offshore pro- duction facilities. This will promote safe, pollution...
API SPEC 2B pdf download
API SPEC 2B pdf download.Specification for the Fabrication of Structural Steel Pipe 1 Scope 1.1 This specification covers the fabrication of structural steel pipe formed from plate steel with longitudinal and cir- cumferential butt-welded seams, typically in sizes 14 in. out- side diameter (OD) and larger (40 in. and larger for LWDS) with wall thickness 3 / 8 in. and...
API Spec 15LR pdf download
API Spec 15LR pdf download.Specification for Low Pressure Fiberglass Line Pipe and Fittings 1 Scope 1.1 COVERAGE This specification covers filament wound (FW) and cen- trifugally cast (CC) fiberglass line pipe and fittings for pipe in diameters up to and including 24 in. in diameter and up to and including 1000 psig cyclic operating pressures. In addition, at the manufacturer’s...
API Spec 8A pdf download
API Spec 8A pdf download.Specification for Drilling and Production Hoisting Equipment 1 Scope 1.1 DESIGN RATING BASIS This specification provides a basis for establishing the ratings of main load carrying components of certain hoist- ing equipment used in drilling and production operations as follows: 1.1.1 Maximum Load Rating This is a calculated maximum load rating using a pre- scribed design...